Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums
  • jeepsr4ever's Avatar
    Yesterday, 07:17 PM
    The standard post you are using will work. You may have a tool (Tool 101) that may be an air scribe already.
    1 replies | 6 view(s)
  • ggeh's Avatar
    Yesterday, 06:48 PM
    what post processor do I need in sheetcam to run plate marker/scribe? I see some there but not sure if they are the right ones.
    1 replies | 6 view(s)
  • jeepsr4ever's Avatar
    Yesterday, 02:02 PM
    Gain in pressure not loss. You will get a loss if you put the grooves up towards the top of the motor
    2 replies | 9827 view(s)
  • jeepsr4ever's Avatar
    Yesterday, 12:40 PM
    Look in your plasma cutter book. This will give you speeds per amperage, per material as well as tip voltage and pierce delay/pierce time
    7 replies | 92 view(s)
  • Heavy_Metal_Thunder_81's Avatar
    04-23-2017, 02:17 PM
    I was JUST going to ask this. You can still get the gaskets but a STEEL or thick aluminum block off plate would be great.
    1 replies | 1275 view(s)
  • Heavy_Metal_Thunder_81's Avatar
    04-23-2017, 01:33 PM
    Have you noticed any significant loss in overall oil pressure?
    2 replies | 9827 view(s)
  • ggeh's Avatar
    04-23-2017, 07:12 AM
    This is what I cut at (65 amps cut speed 280, 124 volts) What would you suggest. My hyperthem has a range of 25amps to 85amps. I have no info on...
    7 replies | 92 view(s)
  • tufcj's Avatar
    04-22-2017, 02:47 PM
    tufcj replied to a thread 78 AMC 401 heads in Engines
    360 and 401 heads are the same. If you have the iron heads done, they're always worth something if you want to upgrade to aluminum later. Bob...
    5 replies | 59 view(s)
  • Kwish's Avatar
    04-22-2017, 09:07 AM
    Kwish replied to a thread 78 AMC 401 heads in Engines
    Awesome thanks for the input, I'll probably just stick with the stock iron heads than! I'll just have the machine shop go through them.
    5 replies | 59 view(s)
  • tufcj's Avatar
    04-22-2017, 07:50 AM
    tufcj replied to a thread 78 AMC 401 heads in Engines
    For a trail rig, low RPM torque, little high RPM use, I'd probably stick with the stock iron heads and have a quality 3 or 5 angle valve job and some...
    5 replies | 59 view(s)
  • Kwish's Avatar
    04-21-2017, 08:23 PM
    Kwish replied to a thread 78 AMC 401 heads in Engines
    My budget will allow it, and I've got an Edelbrock performer intake and cam to go with the heads. Also I plan on just keeping the bore stock if I can...
    5 replies | 59 view(s)
  • tufcj's Avatar
    04-21-2017, 07:55 AM
    tufcj replied to a thread 78 AMC 401 heads in Engines
    Big weight savings on the aluminum heads. It will really depend on what you do as far as the bottom end of the motor. Cam and compression will make...
    5 replies | 59 view(s)
  • jeepsr4ever's Avatar
    04-21-2017, 07:48 AM
    The secret to cutting diamond tread or tread plate is to use a slightly higher tip volts so your torch will never collide with the diamonds
    7 replies | 92 view(s)
  • Kwish's Avatar
    04-21-2017, 07:17 AM
    Kwish started a thread 78 AMC 401 heads in Engines
    Finally getting everything ready to start building my 78 401 out of my Wagoneer, Debating on whether I should buy Edelbrock RPM heads or if I should...
    5 replies | 59 view(s)
  • ggeh's Avatar
    04-20-2017, 10:36 AM
    Ok I can do that. What about height control that raises and lowers for the diamonds so the torch doesn't collide with diamonds?
    7 replies | 92 view(s)
  • jeepsr4ever's Avatar
    04-20-2017, 08:22 AM
    When your cutting diamond plate you need to consider the diamonds. You cannot cut it using a tool set up for the thinnest area. You need to use a...
    7 replies | 92 view(s)
No More Results
Bulltear Ad