PDA

View Full Version : How was your weekend?


Bulltear Ad
Bulltear Ad

jeepsr4ever
07-11-2004, 09:12 AM
Mine was good except for a concussion I recieved saturday afternoon form a boating accident. Still havent gotten a tan.. I know jeep bud is chuckling right now.

Anyone have anythign exiting happen?

rollen dean montoya
07-11-2004, 11:11 AM
spending the weekend with gail :t: today we are going to pioneertown
movie set to gunfight :mrgreen: and spend time with the grandson.
later, rollen :lo1l:

jeepsr4ever
07-11-2004, 11:37 AM
rollen how many tv shows/ movies ya been in?

cheapjeep
07-11-2004, 01:06 PM
Mine was good except for a concussion I recieved saturday afternoon form a boating accident. Still havent gotten a tan.. I know jeep bud is chuckling right now.

Anyone have anythign exiting happen?

I hope whatever you hit with your head is okay :wink: . I have done nothing this weekend :t: . Okay I did work on the Bronco a little but that will be neverending. If you want a tan come out to Vegas, you can get a tan in your house in the summer :!: .

tufcj
07-11-2004, 02:53 PM
:? Got my 390 back from the machine shop Saturday afternoon. Re-cleaning the block today, coating the lifter valley with Glyptal, checking all clearances, and hopefully getting the crank set in. I re-check everything done by the machine shop. It's easier to check/correct now than have to take it back apart later, or worse, have the engine come apart.

Mudrat
07-11-2004, 07:48 PM
SAT - Got most of the YJ dash back in - have some turn signal issues in the rear harness. When the left is blinking the right running light dims and vs vs when the right blinks the left dims?? :razz:

Sun, worked a chainsaw for about 5 hours cleaning up the last tree from the hurricane. Just when I was calling it quits :razz: :razz: :razz: (about 2:30) the neighbors boy comes over with a problem with his Neon. Can't get the front hub off to install new studs (he said the "service shop" cross threaded 3 of 5 and one snaped off at the hub face, the other two are unservicable!!)
Long story short - MC to the rescue (except his cell never seems to be charged??)
Well at 6 we dropped by AZ and rented a major-kinetic-energy-slam-hammer-wheel-puller. 4 whacks and the sum-beotch came off - with only 1/2 the 8) sealed bearing that kept everything stuck in place (the inner race was seized on the hub shaft). :razz: :razz: :razz: :razz: :razz:

Now. How in the heck are we going to get the other 1/2 of the 8) sealed bearing out??

Mudrat

jerry
07-11-2004, 10:07 PM
mowed the yard about 3 acres it take a while we are mowing 2 time a week I guess it's all the water a fertilizer. We have the big pig roast coming up July 24 this will be the 12 yr. anybody be in Eugene come on down.


Jerry

rollen dean montoya
07-11-2004, 10:20 PM
ccouple of front pages in the desert dispatch newspaper. billboards and
tour brosures in asian countries. the gun monster(arms specialist) for
a french documentary. the girl was cute! :mrgreen: :t:
later,rollen :lo1l:

jeepsr4ever
07-12-2004, 09:09 AM
Their should be another lip on the backside of the bearing just before the retainer. Tell your neighbor you want him to brign the spindle in for servicing, without the right tools you wont be able to pull the bearing



Sounds like you guys had a busy weekend....yeah cheapjeep it was south lindstrom Lake....People on the beach thought I was dead :!:

Mudrat
07-12-2004, 01:48 PM
Their should be another lip on the backside of the bearing just before the retainer. Tell your neighbor you want him to brign the spindle in for servicing, without the right tools you wont be able to pull the bearing


?? Do you have a drawing of the spindle and how the bearing goes in? When it all came apart, the hub with the inner race seized to it, what stayed in the spindle was the outer race and balls for the bearing. There is no way I could see to get anything behind the outer race. Unless we pull the spindle off - and that looks like a MAJOR pain!! Struts, ball joints, upper and lower arms etc... there has to be an easier way. :-| Oxy and Acetylene??

Thanks - I'm begining to hate American made Jap-Crap!!
:!:
Mud

jeepsr4ever
07-12-2004, 01:59 PM
Tell your neighbor you want him to brign the spindle in for servicing, without the right tools you wont be able to pull the bearing


:wink:

Mudrat
07-12-2004, 02:10 PM
Tell your neighbor you want him to brign the spindle in for servicing, without the right tools you wont be able to pull the bearing
:wink:
I caught that part - how do we get it from his moms driveway to the service shop without a left front wheel? I guess I'm not that creative in getting a 3 wheel POS on my trailer?!

Mudrat

rollen dean montoya
07-12-2004, 03:37 PM
got a tranny dolly? thats how we got the eagle onto a flatbed trailer.
damn near maxxed out the gvwr of the ford f-150 and trailer. did you
know eagles with a full tank weigh 4750 :shock: anyways, thats my 2cents
worth :mrgreen:
later, rollen :lo1l:

Mudrat
07-12-2004, 04:37 PM
got a tranny dolly? thats how we got the eagle onto a flatbed trailer.
damn near maxxed out the gvwr of the ford f-150 and trailer. did you
know eagles with a full tank weigh 4750 :shock: anyways, thats my 2cents
worth :mrgreen:
later, rollen :lo1l:

Well I'm not worried about the weight - 12,000 lb trailer and the truck can handle it all. And Nope dont have a tranny jack. We have the car on wheel dollies now with the bare spindle sitting on a 2x4. Need to figure out how to make it semi permanent so we can wheel it to the trailer. Getting it up the ramp will be the challenge. Well, a 12,000 lb winch outta do it though.

The problem for the kid is getting the $$ to pay for the repair.

Mudrat

pyagid
07-12-2004, 05:38 PM
Need to figure out how to make it semi permanent so we can wheel it to the trailer. Getting it up the ramp will be the challenge. Well, a 12,000 lb winch outta do it though.

The problem for the kid is getting the $$ to pay for the repair.

Mudrat

http://www.yagid.com/newproject.html

on 3 wheels it should be easy

Mudrat
07-12-2004, 06:15 PM
Hehehehe Yeah, I remember that now :?
Sorta the same type trailer, but I have 2 equipment ramps rather than a gate/ramp.
http://members.cox.net/mudrat/87%20YJ/YJ_on_trlr.JPG

Have the same type 4-wheel dollies - currently under all 3.25 wheels :shock:
Could build a plywood ramp and winch it up. Getting it off at the shop??? Push and pray :shock:
The problem will be getting a macpherson strut and the dolly to stick to each other. Suppose a 1500 lb tie-down stap would work?? I'll need the 10K straps for the 2400 lb POS.

Ya know :-| he's gunna owe me some serious beer for this!!!

Mudrat

edaddi
07-13-2004, 09:12 PM
I had a good day wheelin Sunday. Pics at --> http://www.mudrunner.com/pics/album18

Mine is the white jeep...and the pictures of the jeep on 3 wheels.....well I found a pretty deep hole under a collection of sticks.... :mrgreen:

cheapjeep
07-13-2004, 09:35 PM
edaddi, cool pic's :lo1l: . Look's like you had a lot of fun =D>

rollen dean montoya
07-13-2004, 10:25 PM
nice pix :t: mudrat hope this guy has at least a keg for ya :razz:
later, rollen :lo1l:

pyagid
07-14-2004, 06:48 AM
looks Like a lot of fun :t:

was this your passenger when you got up on 3 wheels :shock:


-Paul

Mudrat
07-14-2004, 08:06 AM
edaddi - awsome pics dude!!! That place looks like it had a bit of everything we build for!!!

Mudrat
Thanks Dog, haven't seen the kid in 3 days...still have his rent money he put out for the puller so I do expect to see him again :lo1l: 'Rat

rollen dean montoya
07-14-2004, 08:38 PM
well then you should get 1 keg and 1 case of jack daniels :t: the jack
is for interest :mrgreen: :razz:
later, rollen :lo1l:

Bulltear Ad