View Full Version : 360 build
Mudrat
04-16-2005, 07:20 PM
OK, It's finally making progress.
I've got the heads done - waiting my roller rockers
Had a hell of a time getting the dizzy gear off the cam, yeah, I broke it :(:
http://members.cox.net/mudrat-jeeper/Busted-cam-gear.JPG
So I wound up taking it all out together!! :shock:
http://members.cox.net/mudrat-jeeper/Cam_%26_timing_set.JPG
http://members.cox.net/mudrat-jeeper/Timing_chain_%26_cam.JPG
So I FINALLY got the crank out, and did the oil mod drilling the mains out to .339 (if this doesn't work MC, you owe me a block!!!) I stuck a bit in there to see the angle before just making that TiN bit chew up my block :shock:
http://members.cox.net/mudrat-jeeper/Crank_oiling-2.JPG
Drilled the last 4 mains leaving the front timing chain one un-drilled
If you look close, you can see drillings where the bearings should be.
http://members.cox.net/mudrat-jeeper/Mains_post_drilling.JPG
Now to get this all to the machine shop, have it acid dipped, crank ground and cross drilled, cylenders bored (probably .30), new pistons, cam, etc ... and get it put together.
Mudrat
jeepsr4ever
04-16-2005, 09:24 PM
:t: I bet your greasy now :?:
Mudrat
04-17-2005, 08:04 AM
:t: I bet your greasy now :?:
Sweaty yes, greasy nah :wink: After that I had to settle my nerves and machined up a couple engine lift links - that's when Jack came over =D>
We went down and looked at a Waggie that I'm picking up TODAY!! Everything but the engine, tranny, x-fer. Seats are ragged, but it's all power (seats, windows, locks ...)
Mudrat
Chris
04-17-2005, 08:50 PM
Mudrat,
Sounds like the waggie worked out for you. :lo1l:
jeepmonster
04-17-2005, 09:58 PM
Hey,
Is that the original nylon tooth timing gear? How loose was your timing chain? My 74,000 OM 343 had almost 2" of deflection :!: I bought a rollmaster with a torrington bearing...nice piece!
What was the condition of your pistons/bores? :idea:
Mudrat
04-18-2005, 05:03 AM
Mudrat,
Sounds like the waggie worked out for you. :lo1l:
Not really - - - yet. When I asked for the title, he got reallllly quiet.
I've sent you a PM about this.
Pat
Lifted79CJ7
04-18-2005, 07:23 AM
Hey Pat,
Don't forget to get the little key way guys out of the crank - so your gonna need to get that dizzsy gear off. Trust me, heating it up then spraying a little penetrant oil on it (heat will draw it in) will help in removing them. Also don't loose the keyway from the crank, either!
Jack
fuzz401
04-18-2005, 07:33 AM
take the block out side and scrob it down with dawn disk soap and dow oven cleaner it will clean the block up like new -- the cleaner it goes in the cleaner it comes back :? and if nothing else have it tumble blasted -will have to have it lined bored and redecked but talk about clean
http://img.photobucket.com/albums/v31/fuzzcj7/Picture003.jpg
jeepsr4ever
04-18-2005, 07:48 AM
Fuzz that sucker looks new
fuzz401
04-18-2005, 07:53 AM
http://img.photobucket.com/albums/v31/fuzzcj7/IMG_0503.jpg
it actualy shot peens the block to stress releave it
Mudrat
04-24-2005, 05:23 PM
Well, I finally brought that POS home and got it in the press.
http://members.cox.net/mudrat-jeeper/10tons%2B.jpg
Cranking down on a 20 ton shop press I was afraid I was either going to bust the socket, break the new bearing puller or have success!!!
It was SUCCESS!!! But very near the "I don't want to crank down any more" thoughts :shock:
http://members.cox.net/mudrat-jeeper/Finally.jpg
Now that I have the only piece I needed - the fuel eccentric. I looked at the cam lobes ...
http://members.cox.net/mudrat-jeeper/Bad-lobes.jpg
Wasn't filled with confidence and think I did right with the new cam and a line bore. There were 4 that looked like this...
http://members.cox.net/mudrat-jeeper/Bad-lobes-2.JPG
Now to get it all to the engine shop for a bath, bore, and balance...
Mudrat
04-24-2005, 05:25 PM
Hey,
Is that the original nylon tooth timing gear? How loose was your timing chain? My 74,000 OM 343 had almost 2" of deflection :!: I bought a rollmaster with a torrington bearing...nice piece!
What was the condition of your pistons/bores? :idea:
Yo Monster - sorry, forgot about he question - - nope, both steel. got a rollmaster double roller going in.
Mudrat
Mudrat
04-24-2005, 05:29 PM
it actualy shot peens the block to stress releave it
So THAT'S what this thing is supposed to look like :lo1l: (well, a few silly
milli-meters smaller) :-|
Tried to crank up the pressure washer this weekend and all I got were blisters :smile: I think I have a stuck float or something??? 5.5HP Honda OHV. It'll have to wait till I get back from Charleston - again.
Mudrat
fuzz401
04-24-2005, 05:59 PM
so mudrat when you bring the parts up :?
Mudrat
05-04-2005, 10:23 AM
it actualy shot peens the block to stress releave it
So THAT'S what this thing is supposed to look like :lo1l: (well, a few silly milli-meters smaller)
Mudrat
Well it may not be as "smaller" than I thought. Now that I have it stripped down to parade rest, all the parts in hand or on the way, I finally got it to the shop and what did we findout??? :-|
THIS SUCKER IS ALREADY 40 OVER!!! :shock:
It's going to cost me a hot tank to see if the block is salvageable after all the rust that was in the cylinders :razz:
Glad I didn't pre-order those .030 pistons from ya MC #-o
Jeeze, I'm going to have to either salvage this block or find a buildable one - got too many danged parts for a 360!!!
Mudrat :smile:
Dusty
05-04-2005, 01:47 PM
Nah look at the brite side, everything else you got will work for any AMC. :?: timing set, timing cover, heads, intake, cam bearings ect. doubt you got rods and mains yet since you probably were looking at turning it anyways. .40 over damn man that sucks
fear not 401's are still hiding out there. and can be had reasonable just keep the eyes open and the finger tips in good shape for feeling out that AMC brail :wink:
hopefully the taper is minimal and you can just go with .40 pistons
good luck keep us posted
Dusty
05-04-2005, 04:10 PM
Looks like somebody decided to do the smart thing, i see holes drilled and tapped up top in that block
Lifted79CJ7
05-05-2005, 12:00 AM
That stinks Pat!! Well at least you can still yank a cheapy from UWI!!
Jack
Mudrat
05-05-2005, 05:03 AM
That stinks Pat!! Well at least you can still yank a cheapy from UWI!!
Jack
Well Rob may be able to help me out. He was given a 360 when he bought a Dodge Colt (or Neon or something like that) Wouldn't THAT be a screamer - a 360 in a Colt :shock:
Anyway called him last night to see what it would take to get it out of his garage. If it's rebuildable, I'll strip it down and let the shop have that one to build off of.
Pat
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.