View Full Version : Small displacement AMC with centrifugal blower
tarior
08-19-2005, 03:23 AM
For many years now I have been seeing insanely fast Mustangs with motors smaller than 350 ci, and a centrifugal blower (Paxton or Vortec). I was thinking that maybe someone ought to attempt that strategy with an AMC. Any thoughts?
Barry Kaul
08-20-2005, 07:46 PM
I'd love to that but the problem is finding or making the brackets. I suggested it a while ago under product ideas without much of a response.
tarior
08-21-2005, 03:14 AM
It really can't be too tough to make up a few brackets. I work in metal fab, I can build any bracket a person desires. BTW, I've been at a music fest all day :razz: :razz: :razz: :razz: holycrap wutabuz !!
Barry Kaul
08-21-2005, 08:25 AM
Make up them brackets then!
tarior
08-21-2005, 01:14 PM
All I need is a blower to work with! I don't happen to have one myself. :wink:
Mudrat
09-27-2005, 06:47 PM
It really can't be too tough to make up a few brackets. I work in metal fab, I can build any bracket a person desires.
Anti-wrap spring perches for 2.5" wide springs on a D-44 ;-)
Pat
tarior
09-28-2005, 03:13 AM
Anti-wrap spring perches for 2.5" wide springs on a D-44 ;-)
Pat[/quote]
Describe them
Mudrat
09-28-2005, 06:27 AM
Anti-wrap spring perches for 2.5" wide springs on a D-44 ;-)
Pat
Describe them
Their steel #-o :shock:
OK, ok :wink: ... they look like this, radiused for a D-44 tube (mine are 2.96" diameter - a slight undersize for hand fitting is ok with me), to fit 2.5" wide springs with a 7" long flat top. I don't have the rise height from the top of the tube to the 'flat' but a rough guess is 1".
These as you can see have 3 pin holes for the spring pak.
http://www.tellico4x4.com/catalog/images/products/more/98103.jpg
M.O.R.E. has'm on sale for $38 per pair + shipping (Normally $45) Probably a good deal...
Telico 4x4 wants $46 + shipping to sell the M.O.R.E. part 111!!!
Warrior is getting $24 + freight for the "Stock" size
Lifted79CJ7
09-28-2005, 07:51 AM
Man, I need a set also. But then again, I might just make an antiwrap bar based on a design from www.samsoffroad.com . :-| Shoo, I'm just gonna focus on the motor right now....
tarior
09-28-2005, 11:26 AM
I will check and see if I have the tooling for the brake to make a part that is so narrow inside. Our brake is down at the moment(the brake is broke :mrgreen: ), so I hope you're not in a big hurry. Pester me in a week or so, I have a short attention span. BTW, if I were to just build a set of these on my own time, I'm not sure I could beat $38. But for a set or two, I may be able to sneak a "G"-job in...
eight
09-28-2005, 09:33 PM
I'd just use some 2.5x.25 square tubing and a torch. It's more work to look those up and order them than to just make some if you've got the tubing around.
tarior
09-29-2005, 03:10 AM
Duh! #-o Whack 'em out right quick like that!
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.