View Full Version : Brake Line ?
rollbar
10-19-2007, 06:15 PM
Well Peaches '86 CJ finally is about to blow a front brake line, it's starting to bulge so I need to replace it. I guess I'll go to NAPA & get one, I hope they know the right thread end/diameter.
Simple questions but one I really never paid much attention to.
1. How long is a stock brake line? If memory serves I think they are 17", but the DS & PS are different.
2. W/a stock configuration, how long can I go before it gets in the way (i.e.) hitting the tire etc. 2" longer?
Mudrat
10-19-2007, 07:14 PM
I put 22' braided on Erin's YJ with a 4" lift and 33's
rollbar
11-02-2007, 03:51 PM
Well NAPA doesn't have any & the place I had a link for is no longer & the link does not work. Besides 4WDH etc. does anyone have a link for brake lines that are reasonable, NAPA wants $26.79ea, for stock ones. Would like to get some 20" ones for her stock application.
Soylent_Green
11-02-2007, 09:13 PM
Wont napa make you one? Or perhaps a company like Pirtek.
rollbar
11-02-2007, 09:15 PM
Never thought of that, I'll have to ask them.
Thanks,
Mudrat
11-03-2007, 01:51 PM
The Trailer rebuild guys down the road have DOT approved hoses in various lengths - I was looking there before I knew the lift kit came with them.
rollbar
11-12-2007, 08:42 PM
Well I got them from Advanced & they honored rock autos price :shock: . I was shocked.
So for 15 bucks each (instead of 22-28bucks @various stores) I replaced them today.
Here are the steps to replace your CJ front brake hoses. Thanks for the help Donald :!:
First U have to get the shirt on :rof:
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1060.sized.jpg
Next, loosen the tires lug nutz.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1059.sized.jpg
Here is my buddy Donald jacking up the CJ to begain work.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1058.sized.jpg
Old brake line assy.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1047.sized.jpg
Remove the clip to loosen the brake hose.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1050.sized.jpg
Remove old brake hose. If U can't get the 3/8" line wrench on the spring side of the hard line just use a small flat screw driver & slide the hard line spring back, then the wrench will fit.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1049.sized.jpg
Here R the new / old hoses.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1051.sized.jpg
Remove the original bolt from the old hose & use it on the new one. MAKE SURE U use the new copper washers on BOTH sides.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1053.sized.jpg
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1052.sized.jpg
Sorry, didn't have my camera on close up.
Install bolt in new hose w/the TWO washers & tighten down.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1054.sized.jpg
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1055.sized.jpg
New hose installed & retaining clip.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1048.sized.jpg
Now I use a vacuum pump to suck all the air out of the system. Keep a watch on the master cylinder because the vacuum pump sucks it down pretty quick.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1056.sized.jpg
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1057.sized.jpg
Reinstall the tire.
http://www.street2mud.com/albums/She-love-to-go-Jeepin/100_1059.sized.jpg
Soylent_Green
11-12-2007, 09:19 PM
Good write-up!
:t:
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.