Nicely Built AMC 360 $2000 obo, Norfolk Va 23503

[fifesjeep]

I have a nicely built AMC 360 for sale... Below are some of the parts used... this motor has less than 300 miles on it. The reason for the sale is simple... It's to support the 496 stroker build :!:

AMC 360 bored .030" (4.110") with brass freeze plugs installed, blocks been decked (Can't recall how much) #-o
Edelbrock Carb (Keeping the Holley Carb) :oops:
Edelbrock Performer Intake
Internal Oiling Mod
Heads Milled and Machined, new brass freeze plugs and positive valve seals
AMC Legend Valve Covers (Bulltear special :t: )
Harland Sharp 1.7:1 Roller Rockers
Comp Cams Magnum Chromoly One piece .080" Wall Pushrods
Ross 10:1 Forged Race Pistons
Chromoly Rings
Scat Forged H-Beam Rods with ARP bolts
Clevite Bearings
Crank turned 10/10
Comp Cams 280H Magnum Cam and Lifters
Comp Cams Magnum Timing Set
3 angle vlalve job
10* super locks etc
1 5/8" to 3" Dynomax headers
3" purple hornies (Header mufflers)
Stock manifolds go with it
7.5 quart oil pan (Bulltear Special :!: )
New Water pump
160* thermostat
HEI Distributor
Cardone Distributor with msd Cap adapt
Pro Comp 6al Ignition Module (Keeping the MSD) :oops:
High Energy 50,000 volt coil with aluminum guard
8.5mm wires
Rohl head gaskets

I will have some pics of the motor as well as a video of it idling and me smoking these 35" swampers. 8)

[dan58]

GRR. Can't hold on to it for two months or so? I would take it. Not sure if the price would drop without a carb, headers, the deep pan, valve covers, and such. That 10:1 would be killer with my propane system! :lo1l:

[fifesjeep]

I'd prefer to sell it with everything, this way once it is gone, it's gone and I won't have any parts of an AMC engine laying around.
Worst case scenario is you buy the motor and sell the stuff you don't need. :wink:

I'm heading out to get a video of the beast. I had to start getting out of it towards the end before I ran out of street... or brakes :shock:

http://i7.photobucket.com/albums/y293/Fifesamcjeep82/th_100_1611.jpg (http://s7.photobucket.com/albums/y293/Fifesamcjeep82/?action=view&current=100_1611.mp4)

http://s7.photobucket.com/albums/y293/Fifesamcjeep82/?action=view&current=100_1611.mp4

[dan58]

I hate you. 8) Yeah, color me jealous.

What sort of HP is that ol' girl putting down?

[fifesjeep]

I hate you. 8) Yeah, color me jealous.

What sort of HP is that ol' girl putting down?

Not too sure to be totally honest... I do know that if I hold my foot on the skinny she'll roast those tires a lot longer than what the video showed... :!:

[fifesjeep]

Showed the motor to Eric (Napoleon)... and then I had to burn the tires... again. :t:

[adtarr]

Still for sale?

[fifesjeep]

Still for sale

[adtarr]

Sent you a pm.

[fifesjeep]

Sent you a reply and on your email.

Rich

[fifesjeep]

Still here. :razz:

[GADJIT98]

Still got it? How much?

David

[fifesjeep]

Still got it? How much?

David

Still got it... $2000 and I'm not willing to put it on a pallet etc... it's pick up only.

Rich

[fifesjeep]

Damn... I thought that I found a perfect car to toss this engine in and then I went and looked at it... the subframe is rusted like no other.
http://norfolk.craigslist.org/cto/2024986779.html

[GADJIT98]

Rich,

Does it come with all the accessories (Alt, PS, Brackets, etc)?

can you show me some photos of it?

Thanks,
David

[fifesjeep]

Rich,

Does it come with all the accessories (Alt, PS, Brackets, etc)?

can you show me some photos of it?

Thanks,
David

It'll be a drop in... ie: everything included... I'll have to snap some pics in the morning.

[GADJIT98]

Rich,

Just checking to se if you were able to get those pics yet.

Thanks
David

[fifesjeep]

Rich,

Just checking to se if you were able to get those pics yet.

Thanks
David

it totally skipped my mind... :oops: tomorrow i should have some posted.

[fifesjeep]

Legend Valve Covers
Holley Blue Electric fuel pump with regulator
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/100_1526.jpg
Scat Forged 343 H-Beam Rods
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/000_0408.jpg
Ross 10:1 Forged Race Pistons
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/000_0406.jpg
Harland Sharp 1.7:1... 7/16" studs
Comp Cams 280H Magnum Cam and Lifters
Comp Cams one piece chromoly .080" push rods
Comp Cams Magnum timing set
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/000_0410.jpg

I still have to snap pictures of the motor... I am on 30 days leave so I have plenty of time to take pictures before it gets dark.

[fifesjeep]

A pic of the engine... It's dirty but it is what it is...
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/100_1702.jpg
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/100_1703.jpg
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/100_1705.jpg
http://i7.photobucket.com/albums/y293/Fifesamcjeep82/100_1704.jpg
You can see the Holley air cleaner, eddy 600 cfm carb which is seriously choking this motor... if you toss on a 670cfm to 750cfm carb she's a completely different animal... you can see the eddy performer intake, stock manifolds, high energy coil, procomp ignition module, hei distributor, 8.8mm sparkplug wires, 100amp alt, 7.5 qrt oil pan, this engine will come with extra set of eddy valve covers, and whatever else I can find that hasn't been sold already.