V8 in YJ frame

[pyagid]

Is there anyone that makes motor mounts to put a 360 into a YJ frame? Could i Just grind off the engine mounts on the frame already and use CJ engine mounts? Or am i going to need to make my own? I am just trying to get things prepared for the next stage of my CJ build up and want to try and avoid any snags if possible

http://www.yagid.com/avatar/paulsig.gif

[jeepsr4ever]

I am thinking that more makes those conversion mounts

[Tigger]

Advance Adaptors makes them.

[pyagid]

Advance Adaptors makes them.

I could find them for a CJ....I will have to look again see if I could find the YJ ones or just pick up the phone

http://www.yagid.com/avatar/paulsig.gif

[Tigger]

I could find them for a CJ....I will have to look again see if I could find the YJ ones or just pick up the phone

I will look at my catalog when I get home and get you a P/N.

[pyagid]

found them p/n 713120 (weld in) $164 They are the same part number as the CJ part. Isn't they YJ frame a little wider? ANd would that not make a difference?

[amcpower]

Made my own. Left the Frame mounts on the YJ frame and built a angle braket off of the motor and used the chevy to jeep conversion mount pucks(@$30) Just have to drill out the frame mount for the puck sleve. I run the stock exhaust man., single pipe out the back with the drivers side coming off of the manifold and forward around the oil pan and back to the pass. side and straight back.

[Majo]

Cheaper yet,

Used a reese hitch.

was 3x3 box tube that was at least 3/16 thick ( i forget now) and had 1/4 inch plate on each side when I cut it so it made perfect rise/run with frame rails. Sit's nice and snug too. Can completely Flat skid my YJ with a TJ727 auto. I'll try to find some pics to post sometime. It weird to explain but it came out perfect.

I also got the wiring harnass I made for the v8 swap to a YJ with a 4.2L and Pictures of it, all works good

edit: I got 23 inches of clearance to lowest point on my YJ, it's completely flat skidded, soa'ed on stock springs up front and extended rear with XJ springs, running 35's soon 36 tsl

[Mudrat]

Cheaper yet,

Used a reese hitch.

I also got the wiring harnass I made for the v8 swap to a YJ with a 4.2L and Pictures of it, all works good

edit: I got 23 inches of clearance to lowest point on my YJ, it's completely flat skidded, soa'ed on stock springs up front and extended rear with XJ springs, running 35's soon 36 tsl

Dang!!! Sounds like a sweet setup - do post Pics and Procedures!!! Which motor you drop in it??

Mudrat

[Majo]

I put a 360 in that had original 50k miles each cyclinder pressure tested fine. Thing sat for 4 months started after turning over once. I was like holy poop, cuz I'm a FI fan being an electrical engineer. The harnass I made up I have complete computer drawings for and instructions of what to eleminate, I might team up with MC maybe I gotta PM him send him the layout so he can have it built.

[Majo]

pic of jeep
http://forum.neow.net/index.php?act=Attach&type=post&id=6257


mounts not finished
http://forum.neow.net/index.php?act=Attach&type=post&id=6167

i got lot more bracing in there right now, I dont' have a good top down picture,but because the square tube is like 2.5'' square I can fit an Air rachet in there and use the stock motor mounts so they are dirt cheap to replace, all that reese hitch was 1/4 inch steel btw


wiring harnass pic
http://forum.neow.net/index.php?act=Attach&type=post&id=6171

[pyagid]

Majo nice pics.

I see you are from teh North East? Where abouts are you, I live in CT

-Paul

[Majo]

From lil north of Syracuse, NY small town called Rodman which is right near Watertown.

I've been known to be out in NH and that area alot through VT. I can come by sometime this summer with the YJ, it's totally street legal. Just hope gas is below 3 a gallon

[pyagid]

thats for the offer of swinging by. I actually sold that YJ about 2 weeks after i posted this. I have had a 360 in a CJ for about 5 years now. ANd that is currently going through a rebuild

-Paul