Search:

Type: Posts; User: jeepsr4ever

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    111

    Not enough sold. We took out 45 products and are...

    Not enough sold. We took out 45 products and are eliminating more due to the lack of interest.
  2. Give it a little push it will drop it. There may...

    Give it a little push it will drop it. There may be a tiny burr holding it up. The reamer is the last thing to enter the hole so if it kicked off a but as it left it would keep the plunger from going...
  3. Replies
    1
    Views
    347

    Hard to say. Like saying my car is noisey. Need...

    Hard to say. Like saying my car is noisey. Need more info or video
  4. Replies
    1
    Views
    232

    Vista will not work at all. You need 32 bit xp....

    Vista will not work at all. You need 32 bit xp. Use the pre 2014 legacy master installer. Install mach 3 first then the bladerunner dthcii pre 2014
  5. Replies
    5
    Views
    3,100

    Sticky: No special grease needed.

    No special grease needed.
  6. I think he found his issue. It is a retrofit Gary...

    I think he found his issue. It is a retrofit Gary did on an older Star Lab
  7. No ZDDP cannot do that ya knucklehead. Your...

    No ZDDP cannot do that ya knucklehead. Your over-revving did that but maybe there is more to it. You may or may not have had good valve spring pressure and you most likely hit a valve. You dont break...
  8. 1. You have disable hold checked 2. It looks...

    1. You have disable hold checked
    2. It looks like you have a stuck key on your keyboard
  9. Replies
    5
    Views
    3,100

    Sticky: Just Standard grease. Do not use any high end...

    Just Standard grease. Do not use any high end grease as some might have a PH that is not neutral.
  10. Replies
    1
    Views
    401

    The thread type is 3/4-16 NOT ACME standard...

    The thread type is 3/4-16 NOT ACME standard threads. You can use ACME if you can tap the threads to ACME but there will be no advantage other than telling folks you have ACME adjusters.
  11. Cuts look GREAT!

    Cuts look GREAT!
  12. Replies
    3
    Views
    477

    Sometimes a straight edge will tell you where the...

    Sometimes a straight edge will tell you where the misalignment is. It could be even in the idler wheel on the drivers side. If the upper part is cocked that will do it. Make sure that wheel is...
  13. Replies
    3
    Views
    477

    Misalignment is the ONLY way a serpentine belt...

    Misalignment is the ONLY way a serpentine belt squeaks unless it is so loose it isnt gripping at all. Check for misalignment...you definately have it somewhere
  14. Replies
    1
    Views
    366

    Good talking with you. Let us know if the issue...

    Good talking with you. Let us know if the issue gets resolved
  15. Replies
    7
    Views
    972

    When you boil it down you only need 1 5 way valve...

    When you boil it down you only need 1 5 way valve and 2 regulators. Your post is not set up to turn on both outputs at the same time.
  16. Replies
    7
    Views
    972

    The air cylinder on the scribe is what sets the Z...

    The air cylinder on the scribe is what sets the Z depth. Youll never be able to use an air scribe that is rigid mounted without a slide and air cylinder and a torch at the same time.
  17. Replies
    7
    Views
    972

    The post you have been using for flat cutting...

    The post you have been using for flat cutting also control the scribe. So if you go to Sheetcam/Options/Machine/Post processor/edit then put in these offsets for the scribe.

    X -14.265
    Y -59.18
    Z...
  18. Replies
    7
    Views
    972

    The standard post you are using will work. You...

    The standard post you are using will work. You may have a tool (Tool 101) that may be an air scribe already.
  19. Replies
    2
    Views
    11,702

    Gain in pressure not loss. You will get a loss if...

    Gain in pressure not loss. You will get a loss if you put the grooves up towards the top of the motor
  20. Replies
    7
    Views
    827

    Look in your plasma cutter book. This will give...

    Look in your plasma cutter book. This will give you speeds per amperage, per material as well as tip voltage and pierce delay/pierce time
  21. Replies
    7
    Views
    827

    The secret to cutting diamond tread or tread...

    The secret to cutting diamond tread or tread plate is to use a slightly higher tip volts so your torch will never collide with the diamonds
  22. Replies
    7
    Views
    827

    When your cutting diamond plate you need to...

    When your cutting diamond plate you need to consider the diamonds. You cannot cut it using a tool set up for the thinnest area. You need to use a tool set up for a thickness more towards the thicker...
  23. Replies
    7
    Views
    827

    What thickness?

    What thickness?
  24. Replies
    2
    Views
    1,390

    Sticky: Xpress parts is our #1 choice of 2nd party...

    Xpress parts is our #1 choice of 2nd party shipping. Google them if you want to order.
  25. Edge starting is easy to do you just move your...

    Edge starting is easy to do you just move your part or parts using the 4 way arrow in sheetcam. Then pick the egde of the plate as a zero point in either X or Y depending on how your edge starting....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Bulltear Ad