I just wanted to update what i have been doing. My 4x4 table is still running strong and making money i still need to finish my 5x10. I have been waiting on finishing my 5x10 because i just built a...
Type: Posts; User: wickedinhere
I just wanted to update what i have been doing. My 4x4 table is still running strong and making money i still need to finish my 5x10. I have been waiting on finishing my 5x10 because i just built a...
Getting one rail on its going slow but its going. LOL
http://i20.photobucket.com/albums/b235/wickedinhere/photo588.jpg
I finally got all the Christmas orders out so i had some time to work on my 5x10 its gettin close.
http://i20.photobucket.com/albums/b235/wickedinhere/photo581.jpg...
I sent an email to tom. I did the test feature on the electronics box and i am getting the test voltage of 100 then 150 and the up and down lights light up as the voltage changes. I am not sure if...
60
Oh no that works just great no problem with sheetcam that is all working fine. I am talking about when its cutting the THC will raise .20 and never go down and that will cause it not to cut all the...
I am talking about the limits in mach 3 under settings its raising the torch to high during cutting when using the THC when it decides to move. THe problem with mach 3 is the THC doensn' t work for...
Yes i pressed enter, it had saved before but for some reason it went back to 1 inch. The reason i checked it was because it raised the torch .20 and i had the max set on .12 i was just trying to stop...
Banging head. LOL ok I set the limits so that it wouldn't raise up too far when i first started using the thc well the limit went back to 1 inch and it wont let me change it.
I dont have anything...
How do i trouble shoot that?
Well still not working right for some reason. I put in all the info in the cut profile but it hates me .LOL I set the preset volts to 117 like the book says, start cutting and the tip volts will go...
Ok got it.
Here is a pic of the settings, i completely forget about the cut profile settings i will adjust them next. What about the 60% setting above is that correct or should i change that?...
Ok got it i changed it to 20 and it was alot better I will try changing the span gap.
My THC rate is at -30 that was the setting it was at i did change it. Should it be a negative number? I would think it be 30 or +30 not -30.
My THC seems like its not reacting fast enough i normally cut 16 gauge and its pretty wavy. By the time the thc reacts and moves up it needs to move back down but takes too long and the torch is too...
Not yet i have been so busy i haven't had time to finish it. If it slows down after Christmas i should be able to get it finished.
I am still building the new 5x10 this was on my 4x4. I keep waiting on a break to finish the new table, maybe after the first. LOL
I figured the jumper in the black box was wrong and it was plus a little user error.LOL I finally had some time to fool with it and it works great now.
It makes a world of difference now that it...
Cool
I would say some "how to" videos on mach3/sheetcam that would be great.
Old school 4x4
http://www.youtube.com/watch?v=oHy-nJvQxyg&feature=g-upl
I finally got to cut some 1/4 on my table to make my adjustable feet for my 5x10. It took a little fine tuning but the cuts came out great i just had to slow it down from 60ipm to 50ipm from the book...
It seems to be going faster than i thought it would, I plan on making the leveling part for my legs tomorrow. Its so hot down here i start work about 5:30am before it gets unbearable.
220I got some welding done this morning.