thanks, i copied it, and also put it on my portable hard drive.
Got it reinstalled, then going back through set up I needed a file from CandCnC so I downloaded this
MasterInstaller X Legacy...
Type: Posts; User: Mav68erick
thanks, i copied it, and also put it on my portable hard drive.
Got it reinstalled, then going back through set up I needed a file from CandCnC so I downloaded this
MasterInstaller X Legacy...
Today i go out to the and attempt to load Mach 3. Used it 3 days ago, computer is not hooked up to internet at all. Well Mach 3 crashed with some sort of mach 4 error. Long story short wouldnt load....
Never read anything about accel decel rates when running higher feedrates and Ive read alot, Honestly I havent cut prolly as much near as others have, dont think I cut but maybe 5 things over the...
And all the settings match +60.0 -30 Ive adjusted fthe delay anywheres from .1 to 1 span gap volts on the profile was set at 9/4 ive changed it from 1/4 to 4/4 really dont know why they didnt make...
Ya really frustrated, Im to the point I dont ever wanna cut anything thinner then 11 gauge on this table. Basic shapes are ok anything with detail close lines or alot of pierces forget it. Seems like...
14gauge, I added some ears towards the back to bend down for added support was gonna take it to work and bend it. Never did it doesnt really need it. I wish I did a hole test prior to cutting like...
thanks yeah z ref was set to 10, everytime I read 500 I assumed thats what it was preset at, somehow I must have changed it, I knew there was no way the table traveled 19inches as it would zero 100%...
Matt I remember reading or you bringing this up before, what or where should I be looking in reference to stopping my z from zeroing after every pierce?
1. Can I set it to zero after X number of...
Made my mom a bday present yesterday 3 days late but hey she gets what she gets = P, today I cut the butterfly out. Thinking I just seen that changing color paint in rustoleom, paint the body and...
never thought about different pierce height before on a different layer
thats what the backside of my 1/8th looks like that Im cutting now, looks bad. But I bought a Pistol grip needle scaler from northern tools, lay the piece on some cardboard on the floor and hit it,...
also I had to get the box to run my ground cable through for my powermax65, I think If I remember right I wasnt getting volts feedback or an arc ok signal I cant remember.
have you tried cutting with the THC off? to see if it still doesnt work, try that, I dont even use the thc on thick stuff or things that arent very big, if the cut is X amount of seconds I just dont...
was gonna go safety orange prolly a good thing menards didnt have it. then grabbed black, was like eh... Had machine gray in my hand just couldnt do it, so there was blue red and yellow, Red just...
wicked do you ever get your consumeable sticking error on your plasma, if the 45 shows that. Ive added delay at the end of a cut to help clear out the nozzle but it must be a controller issue because...
Just wanted to pop in and say hey, I really like the new design of the new gantry it makes me sad = P, havent been doing to much working 6 days a week 7 last just to get extra cash to buy stuff for...
on 3/16 its only about .010 difference top to bottom now that I seperated layers. before it still wasnt bad I just wanted to test for improvement, but if I want a 1/2 hole for a bolt to go through I...
peoples r sneaky, I popped in there yesterday and it was funny, under the cut quality I keep reading and usually its Jim saying cut circles at 80% or slow down on corners arcs etc. so Sat. I was...
hey wicked havent logged in a while havent cut much either to cold = P did cut some disc brake brackets for someone and motorcylce brackets.
I dont even bother with the Thc, If you have multiple...
well I got the diamond plate to cut ok, its cutting large areas of 16ga that was the issue, we were trying to cut windmill sides, well when we got done there wasnt much material left and my torch...
Painted with 10-32 hardware, Flat black 1. Polish chrome on the skull and letters... looked like crap so I rinsed it off with water and was still tacky and stuck so I blew it off with air. let it set...
Well its been awhile been busy working testing out ideas being lazy. But noticed the new machine kinda sad I didnt wait a little bit, but being realistic I dont wanna route, I just like the added...
I had my circles at first, and it still labeled everything as S1 S2 S3 etc for pierce locations. Then I re-edited my dxf and made the centers Points and deleted the circles same thing, Labeled all...
Ok so I was cutting some aluminum and my holes are .060 diamter, and my aluminums .060 thick. well cant really cut the holes right. And dunno why Hypertherm doesnt give any fine cut charts for...
AutoCAD r14 its like 10 yrs old. Some dxfs I dl don't show up. I got it forto work a bit on my new 64 bit laptop but it still crashes if you click to many buttons to fast