Search:

I notice a change in noise coming from my x axis drive, It only does it in one direction not the other. Cant seem to pinpoint it if its from the motor or sprocket bearing. Has any one else...

I found the issue, it was my Z limits set to tight. I opened it up to the max and it worked fine. I'm using Linux Commandcnc ver. 0.9.2. Linux is new to me but seems user friendly. It has a message...

Has bulltear industries came up with an angular cut attachment for a cnc plasma cutter? I know a while back there was some talk about one in the works, did it ever come to light?

Thanks, Gary

I sent this to Lance at candcnc but haven't received a reply yet so I thought Id run this by you guys and see what you think.
I have to put check in skip touch offs and also disable hold to get my...

I think i have that figured out my name comes up in sheetcam with a number and says Im registered. Thanks Gary

I changed over from a windows computer to linux computer. the linux computer came with sheetcam on it. I need to transfer my sheetcam license from the windows computer to the linux computer. I dont...

I have a 4x4 bulltear table, using sheetcam, and mach3 . the control box is a candcnc espII-A. I have a floating head with a magnetic mount for the torch and a the scribe is on a air slide that is on...

Ok i found it and got the x and y done but have some trouble geting z offset perfect. X and y seems good but z is either to low or high. Maybe im not doing it right to get the correct mesurement. I...

I was trying to find the right processor to enter the offsets in so I can run the scribe and then the torch.

what post processor do I need in sheetcam to run plate marker/scribe? I see some there but not sure if they are the right ones.

This is what I cut at (65 amps cut speed 280, 124 volts) What would you suggest. My hyperthem has a range of 25amps to 85amps. I have no info on settings below 45amps. does anyone know of settings...

Ok I can do that. What about height control that raises and lowers for the diamonds so the torch doesn't collide with diamonds?

1/8"

I tried to cut some aluminum 1/8" diamond plate, diamonds up. The torch contacted the first diamond it came to and kicked it off the magnetic mount. So I flipped the plate over and tried again and it...

I installed the new I/O card and turned on the control box and then mach3 and I get (wakeup client board does not respond) So I don't have any lights on the green cat5 that plugs into the PC Ethernet...

Matt, you always take good care of me and I appreciate that. I also know you run a 1st class business and Your a very busy man with the plasma, the jeep stuff and all the forums. You already told me...

Matt I ordered a new Table I/O card from CandCNC. After talking with them about the difference in brightness of LED's and it didn't change when I shorted across, they seemed pretty sure the card is...

I shorted across the Z home terminals on the circuit board in the control box and the lite comes on very dim, the same as it does when I operate the Z-home switch at the torch slide.

I bench tested the Z home switch and the wire from the control box to the Z home switch and also checked the wires and the Y home switch which is working. The Z and the Y switch and wires tested the...

Z home stopped working. No light in mach diagnostics for Z home. checked switch on torch good, checked wires from Z home switch to control box good. no light on circuit board where the Z home wires...

I'm truly thankful all your help I know I can be a pain in the butt, so thanks for taking the time with me. I ran a separate circuit for the compressor so that should fix the breaker tripping...

Hi Matt not clear on something, did you ship it or do I need to do something before you ship it?

Thank you Matt and the rest of the men that helped fix my screw up. I wont touch anything again I promise. How much I owe you for the fix and shipping?

made the torch fire opposite of normal. fired when torch light off and off when torch lights on. I set the port back like it was, unchecked active low column. do you have a list or chart for all of...

If I did I didn't know I did it. Where do I look? Would this be better if I either send or bring the computer and the controller up to you and and you can fix what ever is not working right, do you...