Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958

Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958

Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958

Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958
Gettin started - Page 8
Bulltear Ad
Page 8 of 10 FirstFirst ... 678910 LastLast
Results 71 to 80 of 96

Thread: Gettin started

  1. 09-05-2011, 02:57 PM #71
    wickedinhere
    wickedinhere is offline
    Thank you from BT Gear Head
    Join Date
    Jun 2011
    Location
    Louisiana
    Posts
    250
    When i do the mp3000 test i get the up and down flashes but each one only flashes 3 times instead of the 5.
    Reply With Quote Reply With Quote
  2. 09-05-2011, 05:02 PM #72
    Mav68erick
    Mav68erick is offline
    Thank you from BT Junior wrench of the Forum
    Join Date
    Jun 2011
    Location
    Jackson, Michigan
    Posts
    124
    wait I must have skipped that part = P or never counted anything.
    Reply With Quote Reply With Quote
  3. 09-05-2011, 05:37 PM #73
    wickedinhere
    wickedinhere is offline
    Thank you from BT Gear Head
    Join Date
    Jun 2011
    Location
    Louisiana
    Posts
    250
    HEre is the test procedures mine does this but flashes 3 times instead of 5.
    Activate the recessed TEST Button on the front panel of the MP3000-DTHC or your unit with the DTHC module installed and connected. The TEST LED should start flashing.The unit goes into a test sequence where the TIP VOLTS DRO is set to 100 and the UP screen LED flashes 5 times. Then the TIP VOLTS DRO is set to 150 and the DOWN LED flashes 5 times. This test sequence repeats until you hit the Test Button again and the TEST LED stops flashing.
    AIf the test does not show the above results the most probable cause is the serial communications is not working between the PC and the MP3000. Make sure you have the right port selected. If you were sent a special serial cable with the RS232 buffer module (see photo) make sure it is installed correctly.
    Reply With Quote Reply With Quote
  4. 09-07-2011, 11:29 AM #74
    wickedinhere
    wickedinhere is offline
    Thank you from BT Gear Head
    Join Date
    Jun 2011
    Location
    Louisiana
    Posts
    250
    WOW got her cuttin today! My first cut was with the THC on(brass nuckles) cut ipm was to slow (85 ipm) but the THC isnt dialed in so it was way out of wack. The second cut(alien head) i turned off the THC and cut at 110 imp and it did great hardly no dross. I used 1/8 material.




    Last edited by wickedinhere; 09-07-2011 at 11:32 AM.
    Reply With Quote Reply With Quote
  5. 09-07-2011, 05:40 PM #75
    Mav68erick
    Mav68erick is offline
    Thank you from BT Junior wrench of the Forum
    Join Date
    Jun 2011
    Location
    Jackson, Michigan
    Posts
    124
    did you get a massive bevel on one side of that alien,
    Reply With Quote Reply With Quote
  6. 09-07-2011, 06:32 PM #76
    wickedinhere
    wickedinhere is offline
    Thank you from BT Gear Head
    Join Date
    Jun 2011
    Location
    Louisiana
    Posts
    250
    No no bevel. Here is a small piece i cut to see how it would do on close cuts it cleaned up good and i painted it.
    Reply With Quote Reply With Quote
  7. 09-08-2011, 03:26 PM #77
    wickedinhere
    wickedinhere is offline
    Thank you from BT Gear Head
    Join Date
    Jun 2011
    Location
    Louisiana
    Posts
    250
    MOre cuts today.


    Reply With Quote Reply With Quote
  8. 09-08-2011, 05:43 PM #78
    Mudrat
    Mudrat is offline
    Thank you from BT ULTIMUS MAXIMUS STATUS
    Join Date
    Feb 2003
    Location
    Back in VA for a while....
    Posts
    5,822
    Send a message via Yahoo to Mudrat
    I just want space to put one!!! My shop is all wood and filled with a Jeep right now :-(

    'Rat
    " “It is said that men go mad in herds, and only come to their senses slowly, and one by one.." -Charles MacKay
    "'The trouble with our liberal friends is not that they're ignorant; it's just that they know so much that isn't so.' "
    -Ronald Reagan
    VOTE
    Reply With Quote Reply With Quote
  9. 09-08-2011, 05:47 PM #79
    Mudrat
    Mudrat is offline
    Thank you from BT ULTIMUS MAXIMUS STATUS
    Join Date
    Feb 2003
    Location
    Back in VA for a while....
    Posts
    5,822
    Send a message via Yahoo to Mudrat
    Quote Originally Posted by wickedinhere View Post
    MOre cuts today.
    Bone Collector - one of my favorites!!
    " “It is said that men go mad in herds, and only come to their senses slowly, and one by one.." -Charles MacKay
    "'The trouble with our liberal friends is not that they're ignorant; it's just that they know so much that isn't so.' "
    -Ronald Reagan
    VOTE
    Reply With Quote Reply With Quote
  10. 09-08-2011, 05:57 PM #80
    wickedinhere
    wickedinhere is offline
    Thank you from BT Gear Head
    Join Date
    Jun 2011
    Location
    Louisiana
    Posts
    250
    Push that ole jeep outside someone will haul it off. LOL
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Bulltear Ad