I need the input gear from a Dana 18 must be 29 teeth, 6 splines, with a 1.375‚Δω shaft. Anyone????
MC you gotta have one somewhere
-RJ
I need the input gear from a Dana 18 must be 29 teeth, 6 splines, with a 1.375‚Δω shaft. Anyone????
MC you gotta have one somewhere
-RJ
1978 Jeep CJ-7 on Won-Tons :D Nv4500/4:1 SOA on ALCANS and mtr's
i can get you a new one for just over cost in jan if you can wait till the middle of jan!
I dont have a case i want to tear apart or a bullgear
[COLOR=#000000]
Featuring www.StarLabCNC.com[/URL] for CNC plasma machines
1-651-433-3689 TOLL FREE 1-855-433-3689
What kind of green we talking here..... I guess i acutally need some other gears as well.. I want to convert one of my D20 to the lower range I happened upon a Broco D20 so I am half way there. I guess I need some more gears I gott take the thing aprt to see what I have... I was looking at this :
http://www.jeeptech.com/convxfer/2.46-20/
and this:
http://www.off-road.com/~jweed/transfer.htm
Let me know...
-RJ
1978 Jeep CJ-7 on Won-Tons :D Nv4500/4:1 SOA on ALCANS and mtr's
i have some old cases around would have to look and see what i have will look next week
best ever 11.669 @ 112.33 mph in 1/4 mile on 33 x 10.50 slicks and 4" lift / 7.358 @ 93.03 mph in the 1/8 mile
I HAVE A CASE ON A 3SPD FROM A 74 CHEROKEE, WOULD IT HAVE ANYTHING YOU NEED?
Fuzz let me know.... there area few gears I need apparently.
mrtazwrench, I think that would be a D20... not sure though, is there a drum brake on the back of the T-case?
Does it look like this?
Easy way to tell, is the rear dif centered Cherokee..... I am pretty sure that will be a D20 already got two of them.
1978 Jeep CJ-7 on Won-Tons :D Nv4500/4:1 SOA on ALCANS and mtr's
I like te "Almost painless" caveateOriginally Posted by 78304CJ-7
Mudrat
" “It is said that men go mad in herds, and only come to their senses slowly, and one by one.." -Charles MacKay
"'The trouble with our liberal friends is not that they're ignorant; it's just that they know so much that isn't so.' "
-Ronald Reagan
VOTE
Yeah.... so far not too bad. I need two gears to compleate the conversion:
18 8 23
18 8 22
MC I know they can be had aftermarket let me know if you can get them and I will send some money your way. Good used ones work too
-RJ
1978 Jeep CJ-7 on Won-Tons :D Nv4500/4:1 SOA on ALCANS and mtr's
I will be able to get them cheap new in jan untill then you may find one of these guys have a used set..........but if you can wait i will order them for you in jan
[COLOR=#000000]
Featuring www.StarLabCNC.com[/URL] for CNC plasma machines
1-651-433-3689 TOLL FREE 1-855-433-3689
MC sounds fine with me, I'm not in any huge rush to do this. When in Jan, like in a week or 5 weeks? Let me know as this has been a fun project and I look forward to working on it besides it is taking up valuable space on my bacement floor .
I need to get my 401 out and start working on it. Then I gotta get my NV4500 going.
1978 Jeep CJ-7 on Won-Tons :D Nv4500/4:1 SOA on ALCANS and mtr's